Contact us if document is not available

Show all documents

SikaCeram®-102 SA

GENERAL PURPOSE, CEMENTITIOUS TILE ADHESIVE FOR THIN BED APPLICATION FOR SMALL AND MEDIUM TILES

SikaCeram®-102 SA is one-pack premixed adhesive consisting of high resistance cements, selected silicon/quartz mineral charges and specific additives,
used as thin bed tile adhesive for permanent fixing of ceramic tiles. It is ready to use with the addition of water.
Suitable for use in hot and tropical climatic conditions.

  • Very good adhesion to most substrates (concrete, cementitious mortar, stone, bricks)
  • Easy to mix and use
  • Excellent workability and thixotropic consistency
  • Single component system
  • Minimized sagging with small format tiles
Inquire Now

Contact us if document is not available

Show all documents

Usage

  • Suitable for bonding high absorption ceramic tiles
  • Indoor application without primer over concrete, cement mortars, bricks
  • Suitable for floor and wall applications
  • Suitable for moisture tolerant natural stone
 

Advantages

  • Very good adhesion to most substrates (concrete, cementitious mortar, stone, bricks)
  • Easy to mix and use
  • Excellent workability and thixotropic consistency
  • Single component system
  • Minimized sagging with small format tiles

Packaging

20, 50 kg bag

Colour

Grey or white powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / CERTIFICATES

SikaCeram®-102 SA follows the main requirements of EN 12004 class C1 T and complies to the requirements of ANSI 118.4 for shear strength.
Product Information

Composition

Portland cement, selected aggregates

Shelf life

12 months minimum from date of production.

Storage conditions

Store in undamaged, unopened, original sealed packaging in dry conditions at temperatures between 5 °C and 35 °C. Protect from direct sunlight, heat and moisture.
Technical Information

Tensile Adhesion Strength

w/p = 0.23Value

Requirement EN 12004, class C1

Initial≥  0.5 N/mm2≥  0.5 N/mm2

Application

Application Information

Mixing Ratio

Add 4.6 to 4.8 L clean water per 20 kg bag of powder

Fresh Mortar Density

~1.50 kg/l (25 °C)

Layer Thickness

Min. 2 mm
Max. 5 mm (locally up to 12mm thickness possible, for leveling purpose)

Ambient Air Temperature

+5 °C min. / +35 °C max.

Substrate Temperature

+5 °C min. / +35 °C max.

Pot Life

~45 min.  (23 °C)  

Open Time

≥  20 min. (23 °C)(12004-2)

Adjustability Time

≥ 20 min. (23 °C)

Applied Product Ready for Use

Floor tiles can be grouted

After 24 - 36 h

Wall tiles can be grouted

After 4 - 6 h

Full traffic / use

After 14 d

Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption

Consumption

The consumption depends on the surface profile and roughness of the substrate and on the size of the tiles and the placing technique (simple placing "floating" or back to back “buttering-floating”).
As a guide:
For 1 mm thickness over 1m2 area approximately 1.5 kg of material.
One 20 kg bag will cover approximately 5.5 - 8.3 m2 at 3 - 2 mm thickness.
Application steps

MIXING

Mix 20 kg bag with the necessary, above mentioned, amount of water, using an electric blender with a suitable mixing spiral at low speed, in a clean bucket, and up to obtain a smooth paste free of lumps.
Use a blender at 500 rpm maximum; do not mix at faster rate because of mechanical strength decay of the cured product.
After blending, leave the product curing for 5 minutes in the mixing container and then briefly stir the mix prior to application. The obtained mix results very creamy, easily spreadable and thixotropic.

APPLICATION

SikaCeram®-102 SA is applied using notched trowel.

The amount of product should be enough to ensure complete wetting of the tiles’ rear. Tiling has to be carried out on fresh glue, exerting an adequate pressure to ensure contact with the adhesive, and thus the perfect bonding. In case a surface film is formed on the adhesive, it is necessary to wipe the trowel on the adhesive layer previously applied. Avoid wetting with water the adhesive already applied, it damages the adhesive.

CLEANING OF EQUIPMENT

Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.

 

Documents