Product Data Sheet Show all documents

SikaCeram®-202 SA

HIGH PERFORMANCE, POLYMER CONTAINING, WATER RESISTANT CEMENTITIOUS ADHESIVE FOR THIN BED APPLICATION OF MEDIUM AND LARGE TILES

SikaCeram®-202 SA is a high performance, one-pack, polymer containing, water resistant, premixed adhesive. Consisting of high resistance cements, selected silicon / quartz mineral charges and specific additives, used as thin bed tile adhesive for permanent fixing of ceramic tiles.
Suitable for use in hot and tropical climatic conditions.

  • Very good adhesion
  • Easy to mix and use
  • Excellent workability and thixotropic consistency
  • Water resistant
  • Extended open time
  • Single component system
Product Data Sheet Show all documents

Usage

  • Suitable for bonding of high absorption ceramic tiles, earthenware, extruded and refined porcelain tiles
  • Suitable for bonding of large size tiles used in industial enviroment, wet areas, swimming pools, facades
  • Suitable for bathrooms, kitchens, balconies, terraces, etc.
  • Indoor and outdoor application over concrete, cement mortars, bricks and plaster
  • For horizontal and vertical areas
  • Suitable for moisture tolerant natural stone
  • Suitable to tile directly on various Sika waterproofing products
 

Advantages

  • Very good adhesion
  • Easy to mix and use
  • Excellent workability and thixotropic consistency
  • Water resistant
  • Extended open time
  • Single component system

Packaging

20 kg bag

Colour

Grey powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / CERTIFICATES

SikaCeram®-202 SA follows the requirements of EN 12004 class C2 E and complies to the requirements of ANSI 118.4 for shear strength.
Product Information

Composition

Portland cement, selected aggregates and polymers

Shelf life

12 months minimum from date of production

Storage conditions

Store in undamaged, unopened, original sealed packaging in dry conditions at temperatures between 5 °C and 35 °C. Protect from direct sunlight, heat and moisture.

Maximum Grain Size

~0.5 mm
System information

System Structure

In normal conditions no primer is required.
However for very high absorbent substrates please refer to Sika Technical Department.
Technical Information

Tensile Adhesion Strength

w/p = 0.23ValueRequirement EN 12004, class C2
Initial≥  1.5 N/mm2≥  1.0 N/mm2
After water imersion≥  1.0 N/mm2≥  1.0 N/mm2

Application

Application Information

Mixing Ratio

4.6 - 4.8 L of water per 20 kg bag

Fresh Mortar Density

~1.50 kg/l (25 °C)

Layer Thickness

Min. 2 mm
Max. 5 mm (locally up to 12 mm thickness possible, for leveling purpose)

Ambient Air Temperature

+5 °C min. / +35 °C max.

Substrate Temperature

+5 °C min. / +35 °C max.

Pot Life

~45 min. (23 °C)

Open Time

~30 min. (23 °C)(EN 1346)

Adjustability Time

~30 min. (23 °C)

Applied Product Ready for Use

Floor tiles can be grouted

After 24 - 36 h

Wall tiles can be grouted

After 4 - 6 h

Full traffic / use

After 14 d

After 21 d - for swimming pools
Consumption

Consumption

The consumption depends on the surface profile and roughness of the substrate and on the size of the tiles and the placing technique (simple placing "floating" or back to back “buttering-floating”).
As a guide:
For 1 mm thickness over 1m2 area approximately 1.5 kg of material.
One 20 kg bag will cover approximately 5.5 - 8.3 m2 at 3 - 2 mm thickness.
Application steps

MIXING

Mix 20 kg bag with the necessary, above mentioned, amount of water, using an electric blender with a suitable mixing spiral at low speed, in a clean bucket, and up to obtain a smooth paste free of lumps.
Use a blender at 500 rpm maximum; do not mix at faster rate because of mechanical strength decay of the cured product.
After blending, leave the product curing for 5 minutes in the mixing container and then briefly stir the mix prior to application. The obtained mix results very creamy, easily spreadable and thixotropic.

APPLICATION

SikaCeram®-202 SA is applied using notched trowel.
The amount of product should be enough to ensure complete wetting of the tiles’ rear. Tiling has to be carried out on fresh glue, exerting an adequate pressure to ensure contact with the adhesive, and thus the perfect bonding. In case a surface film is formed on the adhesive, it is necessary to wipe the trowel on the adhesive layer previously applied. Avoid wetting with water the adhesive already applied, it damages the adhesive.

CLEANING OF EQUIPMENT

Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.

Documents