Contact us if document is not available

Show all documents

SikaPlast®-222 TG

WATER REDUCING AND RETARDING SUPERPLASTICIZING ADMIXTURE FOR CONCRETE

SikaPlast®-222 TG is a polycarboxylate based superplasticizer developed particularly for use in ready mixed concrete to give extended slump retention and high strength development of normal grade concrete mixes. SikaPlast®-222 TG is suitable for use in concrete mixes incorporating pozzolanic materials such as GGBS, PFA and microsilica.
Suitable for use in hot and tropical climatic conditions.

SikaPlast®-222 TG acts by surface adsorption on the cement particles producing steric hindrance as well as electrostatic repulsion between the binder particles which results in higher dispersion, flow and retention. SikaPlast®-222 TG provides the following beneficial properties:
▪ Substantial improvement in workability without increased water
▪ Low risk of segregation
▪ Normal set without retardation (within the dosage limit)
▪ Improved density and surface finish
▪ Improved water tightness
▪ Excellent solution for continuous concrete casting of deep elements
▪ Does not contain chlorides or other steel corrosion promoting ingredients
Inquire Now

Contact us if document is not available

Show all documents

Usage

  • Ready mixed and site mixed concrete
  • High flow concrete
  • Concrete with high water reduction
Concrete with SikaPlast®-222 TG can be used in the following areas of application:
  • Slabs
  • Foundations
  • Walls
  • Columns and piers
  • Piles
  • Pre-stressed concrete structures
  • Bridges and cantilever structures
 

Advantages

SikaPlast®-222 TG acts by surface adsorption on the cement particles producing steric hindrance as well as electrostatic repulsion between the binder particles which results in higher dispersion, flow and retention. SikaPlast®-222 TG provides the following beneficial properties:
▪ Substantial improvement in workability without increased water
▪ Low risk of segregation
▪ Normal set without retardation (within the dosage limit)
▪ Improved density and surface finish
▪ Improved water tightness
▪ Excellent solution for continuous concrete casting of deep elements
▪ Does not contain chlorides or other steel corrosion promoting ingredients

Packaging

1000 L flowbin. Bulk supply in tanker trucks possible on request

Colour

Brown liquid

Product Details

Sustainability / Certifications / Approvals

CERTIFICATES AND TEST REPORTS

SikaPlast®-222 TG follows the requirements of ASTM C494; Type G and EN 934-2
Product Information

Composition

Aqueous solution of modified polycarboxylates, co-polymers

Shelf life

12 months from date of production if stored properly

Storage conditions

Store in undamaged, unopened, original sealed packaging in dry conditions at temperatures between +5 °C and +50 °C. Mix well before using.

Density

~1.05 kg/l (+25 °C)

Total chloride ion content

Nil

(EN 934-2)

 
Technical Information

Concreting guidance

The standard rules of good concreting practice for production and placing must be observed when using SikaPlast®-222 TG in concrete. Refer to relevant standards.
Fresh concrete must be cured properly especially at high temperatures in order to prevent plastic and drying shrinkage. Use Sika® Antisol® products as a curing agent or apply wet hessian.

Application

Application Information

Dispensing

SikaPlast®-222 TG is added to the gauging water or simultaneously poured with it into the concrete mixer at the batching plant.
Do not add SikaPlast®-222 TG directly to the dry mix. For optimum utilization of its high water reduction property, we recommend thorough mixing. The addition of the remaining gauging water (to fine tune concrete consistency) may only be started after two-thirds of the wet mixing time to avoid surplus water in the concrete.

Compatibility

SikaPlast®-222 TG is suitable for mixes containing all types of cement and supplementary cementitious materials such as: Microsilica (Silica Fume), Fly Ash (PFA), GGBS (ground granulated blast furnace slag) and the following Sika products:
▪ SikaPump®
▪ Sika® FerroGard®
▪ SikaFume®
▪ SikaFiber®
▪ Sika® Aer
▪ Sika® Stabilizer
▪ SikaControl®
We recommend to perform trial mixes to establish the required performance when combining SikaPlast®-222 TG with the above products or other admixtures. Please consult our Sika Technical Department.
Consumption

Recommended dosage

0.5 - 2.5 % by weight of binder
Higher dosages by weight of binder may be used depending on the mix design, raw materials, climatic conditions and concrete requirements. Trial mixes must be performed to establish the exact dosage rate required.

Documents