Sikafloor®-1230
Sikafloor®-1230 is a multi-component, self-smoothing, total solids, epoxy overlay system designed to provide continuous protection for concrete floors at thicknesses between 2.0 - 4.0 mm. The cured material produces a dense, colourful, glossy surface. Suitable for use in hot and tropical climatic conditions.
- Easy application
- Smooth high gloss finish for hygienic applications
- Easily cleanable
- Good chemical and mechanical resistance
Usage
Sikafloor®-1230 has excellent wear and abrasion resistance to floors subjected to high volume traffic. The smooth, ultra-dense and high gloss finish is ideal for situations requiring a hygienic, easily cleaned surface. Sikafloor®-1230 may only be used by experienced professionals. Sikafloor®-1230 may be used in the following areas and industries:- Storage warehouses
- Dry production zones
- Engineering workshops and assembly lines
- Showrooms and demonstration spaces
- Plant rooms
- Pharmaceutical facilities, laboratories, and clean rooms
- Dry food processing
- Aircraft hangars
- Retail
- Schools, hospitals, and hotels
Advantages
- Easy application
- Smooth high gloss finish for hygienic applications
- Easily cleanable
- Good chemical and mechanical resistance
Packaging
46 kg multi component pack (including colour pack)
Colour
Available in various colour shades, please request Sika sales representative for colour chart.
Under direct sun light there may be some discolouration and colour variation; this has no influence on the function and performance of the coating.
Product Details
Composition
Epoxy resin, selected fillers and pigments
Shelf life
12 months from date of production
Storage conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5°C and +30°C.
Density
~1.79 kg/l (mixed, at 25°C)
Solid content by mass
~100 %
Note: Total solid epoxy composition acc. to the test method Deutsche Bauchemie e.V. (German Association for construction chemicals)
Abrasion resistance
| ~50 mg (CS17 Wheel / 1000 cycles / 1000 g weight) | (ASTM D4060) |
Resistance to impact
| Passes (2 meters with 1.5 kg) | (EN ISO 6272-1: 2011) |
Compressive strength
| ≥ 85 N/mm² (7 days) | (ASTM C579-93) |
Flexural-strength
| ≥ 35 N/mm² | (BS 6319 Part 3 / ASTM C580) |
Tensile strength
| ≥ 20 N/mm² | (BS 6319 Part 7 / ASTM C307) |
Water absorption
| ≤ 0.05% | (ASTM C413) |
Application
Layer thickness
Min. 2 mm
Max. 4 mm
Ambient air temperature
+10°C min. / +30°C max.
Relative air humidity
80 % r.h. max.
Dew point
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.
Note: Low temperatures and high humidity conditions increase the probability of blooming.
Substrate temperature
+10°C min. / +30°C max.
Substrate moisture content
< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
~35 min (at 25°C)
Applied product ready for use
| Temperature | Foot traffic | Full cure |
| +25°C | ~24 hours | ~7 days |
Consumption
As a general guide:
~1.8 kg/m²/mm applied as a self-smoothing wearing course.
For additional and more detailed information please refer to General Method Statement.
Always prime the surface before application of self-smoothing layer.
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc.
A 46 kg unit of Sikafloor®-1230 will yield ~25.7 L of mixed material.
Sikafloor®-1230 components are supplied in preweighed packs which should not be split or divided. Always mix a full kit.
APPLICATION INSTRUCTIONS
EQUIPMENT
- Vacuum recovery shot blasting machine
- Masking tape / polythene sheets
- Heaters for cold weather work
- Trowels
- Slow speed drill with suitable paddle
- Brushes or short nap hair rollers
- Industrial vacuum
- Scarifier (Errut / Von Arx)
- Grinder
- Overalls
- Lighting
- Spiked roller
- Spiked shoes
- Pin screed
MIXING
Note: Before mixing and application, store Sikafloor®-1230 under cover in an air-conditioned environment and protect it from temperature extremes. Improper storage may affect workability, finish and curing.
- Pour the colour pack into the base (Part A).
- Mix at 300–600 rpm using a slow-speed handheld mixer with a suitable paddle (e.g. Collomix DLX) for at least 1 minute.
- Transfer the mixture into a clean mixing bucket (minimum 30 L).
- Add the Sikafloor®-1230 filler (Part C) while mixing until a uniform, streak-free colour is achieved (minimum 2 minutes), then remix the blend (Part A + colour pack + Part C) for additional 30 seconds.
- Add the reactor (Part B) and continue mixing until a fully uniform, streak-free colour with no visible filler lumps is obtained.
Always maintain consistent mixing times across all batches to ensure uniform colour during application.
APPLICATION
Prior to application, confirm substrate moisture content, relative air humidity and dew point. If > 4 % pbw moisture content, Sikafloor® EpoCem® may be applied as a T.M.B. (temporary moisture barrier) system.
|
|
|
Mixed Sikafloor®-1230 is poured and spreaded evenly by means of a serrated trowel or pin rake.
After spreading the material evenly, turn the serrated trowel and smooth the surface in order to achieve an aesthetically higher grade of finish.
Roll immediately (before material begins to gel) in two directions with a spiked roller to ensure even thickness.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with suitable thinner (Xylene / MEK / Acetone), immediately after use. Hardened and/or cured material can only be removed mechanically.