Sikafloor®-2430
2-PART EPOXY COLOURED COAT
Sikafloor®-2430 is a two part, solvent containing, coloured, epoxy resin based coating. Suitable for use in hot and tropical climatic conditions.
- Good chemical and mechanical resistance
- Easy application
2-PART EPOXY COLOURED COAT
Sikafloor®-2430 is a two part, solvent containing, coloured, epoxy resin based coating. Suitable for use in hot and tropical climatic conditions.
Part A | 5 kg, 10 kg containers |
Part B | 5 kg, 10 kg containers |
Part A + B | 10 kg, 20 kg ready to mix units |
Resin - Part A | Coloured, liquid |
Hardener - Part B | Transparent, liquid |
Epoxy coloured coating according to EN 13813 : 2002, provided with the CE mark
Epoxy
24 months from date of production
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C.
Part A | ~1.30 kg/l |
Part B | ~0.96 kg/l |
Mixed resin | ~0.93 kg/l |
All Density values at +23 °C.
~60 %
~46 %
~88 mg (CS 10/1000/1000) (14 d/+23 °C) | (DIN 53 109) |
Exposure* | Dry heat |
Permanent | +50 °C |
Short-term max. 7 d | +80 °C |
Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (steam cleaning etc.).
*No simultaneous chemical and mechanical exposure.
Part A : Part B = 70 : 30 (by weight)
+10 °C min. / +35 °C max.
80 % r.h. max.
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.
Note: Low temperatures and high humidity conditions increase the probability of blooming.
+10 °C min. / +35 °C max.
< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM-measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Temperature | Time |
+10 °C | ~10 h |
+20 °C | ~6 h |
+30 °C | ~3 h |
Before overcoating Sikafloor®-2430 allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 36 h | 4 d |
+20 °C | 24 h | 2 d |
+30 °C | 16 h | 24 h |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
~0.15 - 0.2 kg/m² applied as a roller coating
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc..
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved.
To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix.
Over mixing must be avoided to minimise air entrainment.
Mixing Tools:
Sikafloor®-2430 must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
Prior to application, confirm substrate moisture content, relative humidity and dew point.
If > 4 % pbw moisture content, Sikafloor® EpoCem® may be applied as a T.M.B. (temporary moisture barrier) system.
Primer:
Make sure that a continuous, pore free coat covers the substrate.
Always apply the first coat of Sikafloor®-2430 by brush when used as a primer.
Seal coat:
Sikafloor®-2430 is spread evenly using a short pile roller.
A seamless finish can be achieved if a “wet” edge is maintained during application.
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.