Contact us if document is not available
Sikafloor®-262 AS N
2-PART, SMOOTH ELECTROSTATIC CONDUCTIVE EPOXY FLOOR COVERING
Sikafloor®-262 AS N is a two part, self-smoothing, electrostatic conductive, coloured epoxy resin covering. Suitable for use in hot and tropical climatic conditions.
- Electrostatic conductive
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Semi-gloss finish
- Slip resistant surface possible
Contact us if document is not available
Usage
Sikafloor®-262 AS N is used as:- Decorative and protective electrostatic conductive self-smoothing system for concrete or cement screeds with normal up to medium heavy wear.
- Suitable as a wearing course in industries, such as automotive, electronics and pharmaceutical manufacturing, storage facilities and warehouses.
- Particularly suitable for areas with sensitive electronic equipment for example CNC machinery, computer rooms, aircraft maintenance sheds, battery-charging rooms and areas subjected to high explosion risk.
Advantages
- Electrostatic conductive
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Semi-gloss finish
- Slip resistant surface possible
Packaging
Part A | 21 kg containers |
Part B | 4 kg containers |
Part A + B | 25 kg ready to mix units |
Colour
Resin - Part A | Coloured, liquid |
Hardener - Part B | Transparent, liquid |
Almost unlimited choice of colour shades.
Due to the nature of carbon fibres providing the conductivity, it is not possible to achieve exact colour matching. With very bright colours (such as yellow and orange), this effect is increased. Under direct sun light there may be some discoloration and colour variation, this has no influence on the function and performance of the coating.
Product Details
SUSTAINABILITY
LEED Rating
Sikafloor®-262 AS N conforms to the requirements of LEED EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings SCAQMD Method 304-91 VOC Content < 100 g/l.
APPROVALS / CERTIFICATES
- Fire classification in accordance with EN 13501 -1, Report No. 2007- B - 0181 / 17, MPA Dresden, Germany, May 2007
- Testing of electrostatic properties in accordance to IEC 61340, SP Institute, Test Report F900355: A, February 2009
- Testing of Paint Compatibility in accordance to BMW-Standard 09 -09 -132 - 5, Polymer Institute, Test Report P 5541, August 2008
- Varnishability test according to VW-standard PV 3.10.7 (paint wetting impairment substances (PWIS)) like silicones, HQM GmbH, Test Report 09 - 09 -132 - 4, 09.2009
- Particle emission certificate Sikafloor®-262 AS N CSM Statement of Qualification - ISO 14644 - 1, class 4 - Report No. SI 1412 - 740, March 2015
- Outgassing emission certificate Sikafloor®-262 AS N F CR: CSM Statement of Qualification - ISO 14644-8, class - 8.0 - Report No. SI 1412 - 740, March 2015
- Spark resistance in accordance with UFGS - 09 97 23 of coating systems, Test report P 8625 - E, Kiwa Polymer Institut
|
|
|
Composition
Epoxy
Shelf life
12 months from date of production
Storage conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5°C and +30°C.
Density
| Part A | ~1.69 kg/l |
| Part B | ~1.03 kg/l |
| Mixed resin | ~1.54 kg/l |
| Filled resin 1 : 0.4* | ~1.73 kg/l |
All Density values at +23 °C
*Filled with quartz sand aggregate of size 0.08-0.20mm: Sikadur®-504
Solid content by weight
~97 %
Solid content by volume
~97 %
Volatile organic compound (VOC) content
| <50 g/l Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (SCQAMD, Rule 1168) |
Shore D Hardness
| ~80 (28 d/+23 °C) Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (ASTM D2240-15) |
Abrasion Resistance
| <50 mg (CS 10 / 1000 / 1000) (28 d/+23 °C) Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (ASTM D4060-14) (Taber Abraser Test) |
Compressive Strength
| ≥70 N/mm2 (28 d/+23 °C) Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (ASTM C579-18) |
Tensile Strength in Flexure
| ~40 N/mm2 (28 d/+23 °C) Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (ASTM C580-18) |
Resistance to Impact
| 1.75 kg-m Filled resin 1 : 0.4 ratio, with Sikadur®-504 | (ASTM D2794-93) |
Chemical Resistance
Resistant to many chemicals. Please contact Sika Technical Department.
Temperature Resistance
Exposure* | Dry heat |
Permanent | +50 °C |
Short-term max. 7 d | +80 °C |
| Short-term max. 2 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (Such as during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Electrostatic Behaviour
| Resistance to ground 1) | Rg < 109 Ω |
| Typical average resistance to ground 2) | Rg ≤ 106 Ω |
1) This product fulfils the requirements of ATEX 137
2) Readings may vary, depending on ambient conditions (such as temperature, humidity) and measurement equipment.
Application
Mixing Ratio
Part A : Part B = 84 : 16 (By weight)
Ambient Air Temperature
+10 °C min. / +35 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +35 °C max.
Substrate Moisture Content
< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperatures | Time |
+10 °C | ~40 min |
+20 °C | ~25 min |
| +30 °C | ~15 min |
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~30 h | ~5 d | ~10 d |
+20 °C | ~24 h | ~3 d | ~7 d |
+30 °C | ~16 h | ~2 d | ~5 d |
Note: Times are approximate and will be affected by changing ambient conditions.
Consumption
| Coating System | Product | Consumption |
| Self-smoothing wearing course (Film thickness ~1.5 mm) | Sikafloor®-262 AS N filled with Sikadur®-504 | Max. 2.5 kg/m2 Binder + Sikadur®-504 Depending on the temperature the filling grade varies from: 1 : 0.1 pbw (2.3 + 0.2 kg/m2) to 1 : 0.4 pbw (1.8 + 0.7 kg/m2) |
These figures are theoretical and do not allow for any additional material required due to surface porosity, surface profile, variations in level and wastage etc.
For detailed information, please refer to the related System Data Sheet.
MIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add Sikafloor®-Filler 1 or the quartz sand 0.1 - 0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimize air entrainment. Sikafloor®-262 AS N must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
APPLICATION
Sikafloor®-262 AS N is poured, spread evenly by means of a serrated trowel example Large-Surface Scraper No. 656, Toothed blades No. 25 (www.polyplan.com). After spreading the material evenly, turn the serrated trowel and smooth the surface in order to achieve an aesthetically higher grade of finish. Roll immediately (within maximum 10 minutes of application) in two directions with a steel spiked roller to ensure even thickness and to remove entrapped air. To obtain the highest level of aesthetic finish, spike roll in two directions at a 90 degree angle, passing only once in each direction.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.