Product Data Sheet Show all documents

Sikafloor®-359 AE

2-PART PUR TOUGH-ELASTIC NON-YELLOWING COLOURED SEAL TOP COAT

Sikafloor®-359 AE is a two part thard wearing, coloured, non-yellowing (UV resistant), polyurethane seal coat.
Suitable for use in hot and tropical climatic conditions. Formerly known in UAE market as Sikafloor®-359 BH / -359 SG

  • Good abrasion and chemical resistance
  • Matt finish
  • Easy application
  • Excellent slip resistance
  • Easy to clean and mantain
  • UV and Waether resistant and non-yellowing
Inquire Now
Product Data Sheet Show all documents

Usage

  • UV resistant seal top coat with good mechanical resistance for broadcasted and smooth surfaces in industrial flooring.
  • Particularly suitable for car park decks, ramps, warehouses, etc.
  • Suitable for application on vertical and sloped surfaces.
 

Advantages

  • Good abrasion and chemical resistance
  • Matt finish
  • Easy application
  • Excellent slip resistance
  • Easy to clean and mantain
  • UV and Waether resistant and non-yellowing

Packaging

Part A: 16.5 kg containers
Part B: 3.5 kg containers
Part A + B: 20.0 kg ready to mix units

Colour

Resin - Part A: Coloured liquid, Hardener - Part B: Transparent liquid
Available in wide range of colour shades. Please request local Sika representative for standard colour chart.

Product Details

Product Information

Composition

Polyurethane resin

Shelf life

12 months from date of production

Storage conditions

Store in a dry area in original sealed packaging at temperatures between +5 °C and +30 °C. Protect from direct sunlight, heat and moisture.

Density

Mixed resin: ~1.40 kg/l (+23 °C), may vary with colour

Solid content by mass

~74 %

Solid content by volume

~56 %

 
Technical Information

Shore A hardness

~89 (28 days cured at +23 °C)

(ASTM D2240)

Tensile adhesion strength

> 1.5 N/mm2 (failure in concrete)

(ASTM D4541)

Temperature resistance

Exposure*

Dry heat

Permanent

+50 °C

Short-term max. 7 d

+80 °C

Short-term moist / wet heat* up to +80 °C where exposure is only occasional (high pressure water jetting etc.)
*No simultaneous chemical and mechanical exposure.

Chemical resistance

Resistant to many chemicals. Please contact local Sika representative for further information.

Resistance to UV exposure

Artificial Accelerated Weathering (UV Exposure):

Conclusion: Pass - Rating 10

No blistering, no flaking, no chalking.

Exposure duration: 500 hours

(ASTM G154)

Application

Application Information

Mixing ratio

Part A : Part B = 82.5 : 17.5 (by weight)

Ambient air temperature

+10 °C min. / +35 °C max.

Relative air humidity

80 % r.h. max.

Dew point

Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.

Substrate temperature

+10 °C min. / +35 °C max.

Substrate moisture content

< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).

Pot Life

Temperature

Time

+10 °C

~45 min

+20 °C

~30 min

+30 °C~20 min

 

Waiting time to overcoating

Before applying Sikafloor®-359 AE on basecoats allow waiting time of:

Substrate temperature

Minimum

Maximum

+10 °C

~36 h

~72 h

+20 °C

~24 h

~48 h

+30 °C~16 h~36 h

* On fully broadcasted basecoats no maximum waiting time applies. Make sure the fully broadcasted surface is free of dirt, oil, dust or any other contamination.
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity. Refer to PDS of relevant base coat for more information.

Applied product ready for use

Temperature

Foot Traffic

Light Traffic

Full cure

+10 °C

~48 h

~5 d

~10 d

+20 °C

~24 h

~3 d

~7 d

+30 °C~16 h~2 d~3 d

Note: Times are approximate and will be affected by changing ambient conditions.
Consumption

Consumption

~0.2 – 0.25 kg/m2/coat depending on system, surface profile (roughness), exposure and area of application.

Note: These figures are theoretical and do not include for any additional material required due to surface porosity, surface profile, variations in level and wastage etc..
Application steps

EQUIPMENT

Sikafloor®-359 AE must be thoroughly mixed using a low speed electric stirrer (300 to 400 rpm) or other suitable equipment.

MIXING

Mix full kits only. Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 3 minutes until a uniform mix has been achieved.
To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over-mixing must be avoided to minimise air entrainment.

APPLICATION

Prior to application, confirm substrate moisture content, relative humidity and dew point. As a seal coat, the product can be applied by roller or squeegee and then back-rolled (crosswise) with a short-piled roller.

 

CLEANING OF EQUIPMENT

Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.

Documents