Product Data Sheet Show all documents

SikaGrout®-105

CEMENTITIOUS, SHRINKAGE COMPENSATED, GENERAL PURPOSE GROUT

SikaGrout®-105 is a cementitious, free flowing, general purpose, non-shrink precision grout with high ultimate strength.
Suitable for use in hot and tropical climatic conditions.

SikaGrout®-105 is an economical and easy to use grout requiring only the addition of water. It offers the following beneficial properties:
  • Easy to mix
  • Very good flow characteristics
  • Non-shrink
  • Adjustable consistency
  • Non-corrosive and iron-free
Product Data Sheet Show all documents

Usage

SikaGrout®-105 is used for grouting in the following:
  • Machine foundations
  • Columns and slabs in pre-cast construction
  • Connections in pre-cast construction
  • Concrete anchors,
  • Cavities, gaps and recesses
  • Base plates
  • Concrete repair
 

Advantages

SikaGrout®-105 is an economical and easy to use grout requiring only the addition of water. It offers the following beneficial properties:
  • Easy to mix
  • Very good flow characteristics
  • Non-shrink
  • Adjustable consistency
  • Non-corrosive and iron-free

Packaging

25 kg bag

40 kg bag

Colour

Grey Powder

Product Details

Sustainability / Certifications / Approvals

APPROVALS / CERTIFICATES

SikaGrout®-105 follows the requirements of CRD-C621-83-10.2 and ASTM C1107.
Product Information

Composition

Portland cement, selected fillers and aggregates, special additives.

Shelf life

12 months minimum from date of production.

Storage conditions

Store in original unopened packaging in cool and dry condition between +5 °C and +35 °C. Protect from direct sunlight, heat and moisture.

Maximum Grain Size

~2 mm

 
Technical Information

Compressive Strength

1 Day

7 Day

28 Days

w/p ratio = 0.13

≥ 20 N/mm2

≥ 43 N/mm2

≥ 50 N/mm2

Tensile Adhesion Strength

≥ 1.5 N/mm2 (concrete failure)

(BS 1881)

Application

Application Information

Mixing Ratio

Consistency

Water per 25 kg bag

Water per 40 kg bag

Water/Powder ratio

Flowable

3.00 - 3.50 L

4.80 - 5.60 L

0.12 - 0.14

Fresh Mortar Density

~2.35 kg/l (25 °C)

Layer Thickness

Min. 10 mm per pour

Max. 75 mm per pour

Ambient Air Temperature

+5 °C min. / +35 °C max.

Substrate Temperature

+5 °C min. / +35 °C max.

Pot Life

~2 h (23 °C)
Consumption

Yield

~12.0 - 12.1 L / 25 kg bag, depending on water addition

~19.0 - 19.4 L / 40 kg bag, depending on water addition
Application steps

MIXING

Add water according to the desired consistency into a clean mixing vessel before slowly adding the SikaGrout®-105 powder. SikaGrout®-105 is best
mixed in a forced action mixer, for 2 to 3 minutes or until the mix is free of lumps, not longer than 5 minutes. Slow speed drill (maximum 500 rpm) can be also used for mixing. Normal tumble type concrete mixers are not suitable. Do not add extra water or other ingredients. Mix only full bags for best results.

APPLICATION

Before pouring, leave the mixed grout to stand for approximately 5 minutes, to allow entrapped air to escape. Pour into the prepared area in such a way that grout has the shortest distance to travel. Ensure that air displaced by the grout is allowed to escape. When carrying out base plate grouting, ensure a sufficient head of pressure is maintained to keep the mortar flowing. All exposed areas of the mortar surface should be kept as small as possible.

CURING TREATMENT

Treat exposed surfaces with Antisol®-WB curing compounds or use other approved curing methods such as polyethylene sheeting or wet hessian. Do not commence fogging until final set has been reached.

CLEANING OF EQUIPMENT

Clean equipment and mixer immediately after application with water. Hardened material can only be removed mechanically.

 

Documents