Contact us if document is not available

Show all documents

SikaShield® P26 MG SA 4 mm

(formerly SikaBit® T-1200 MG SA )                                                                                                                                                                                                                                                                                          Reinforced plastomeric bituminous waterproofing membrane torch applied, upper surface finish with mineral slated flakes

SikaShield® P26 MG SA 4 mm is a high performance plastomeric torch-on sheet waterproofing membrane. It is based on APP modified bitumen, reinforced with a 200 g/m2 polyester non-woven fabric, faced with a layer of mineral slate flakes embedded on the top surface, to protect the membrane from UV radiation and ageing. Bottom side is faced with a polyethylene film.
Suitable for use in tropical and hot climatic conditions.

  • Resistant to ageing
  • Good tensile strength and elongation
  • High resistance to water vapour
  • Good dimensional stability
  • Flexible at low temperatures
  • Easy to install using the torch-on method
  • Good resistance to mechanical impact
Inquire Now

Contact us if document is not available

Show all documents

Usage

SikaShield® P26 MG SA 4 mm may only be used by experienced professionals.
It is used as a waterproofing and roofing membrane for protection of various substrates in a wide range of application.
  • Waterproofing and damp-proofing of basements against percolating water and damp soil
  • Waterproofing of retaining walls and other concrete structures
  • Waterproofing on flat roofs under protective layers or ballast
  • UV exposed flat roofs
  • Waterproofing on balconies, terraces and wetrooms under screed / tiles
 

Advantages

  • Resistant to ageing
  • Good tensile strength and elongation
  • High resistance to water vapour
  • Good dimensional stability
  • Flexible at low temperatures
  • Easy to install using the torch-on method
  • Good resistance to mechanical impact

Packaging

Roll size: 1 m (roll width) x 10 m (roll length)

Colour

Rolled sheet membrane, reinforced with polyester non-woven fabric with Polyethylene film on both sides for ease of installation
Colour: Black

Product Details

Product Information

Composition

Atactic Polypropylene (APP) Modified Bitumen

Reinforcing material

Polyester, 200 g/m2(ASTM D5147)

Shelf life

12 months from date of production if stored properly in original unopened packaging.

 

Storage conditions

Rolls must be stored in their original package, in vertical position and under cool and dry conditions between temperatures of +5°C and +35°C.
They must be protected from direct sunlight, rain, snow and ice.

Length

10.0 m (± 1 %)(ASTM D5147)

Width

1.0 m (± 1 %)(ASTM D5147)

Thickness

4 mm (± 0.2 mm)(ASTM D5147)
Technical Information

Resistance to static puncture

900 - 1000 N(ASTM E154)

Resistance to dynamic puncture

L4 / I4(UEAtc.5.1.9 / UEAtc.4.4.1)

Tensile strength

Longitudinal800-900 N/50 mm
Transversal600-750 N/50 mm

Elongation

Longitudinal45-50 %
Transversal50-55 %

Tear strength

Longitudinal500-600 N
Transversal400-500 N

Joint shear resistance

Longitudinal800-900 N
Transversal600-750 N

Flexibility at low temperature

~-2°C(ASTM D5147)

Softening point

~150°C(ASTM D36)

Water absorption

0.40 % (at 25°C, 24 h)(ASTM D5147)

Watertightness

Impermeable at 4 bar(ASTM D5385)

Application

Application Information

Ambient air temperature

+5°C min. / +50°C max.

Substrate temperature

+5°C min. / +65°C max.
Application steps

SUBSTRATE QUALITY

The supporting structure must be of sufficient structural strength to apply all new and existing layers of the waterproofing build-up. When used as a roofing membrane, the complete roof system must be designed and secured against wind uplift loadings. The substrate must be uniform, firm, smooth and free of any sharp protrusion or burrs, clean, dry, free of grease, oil, dust and loosely adhering particles.

SUBSTRATE PREPARATION

Use the appropriate preparation equipment to achieve the required substrate quality.

Documents