Contact us if document is not available

Show all documents

Sikadur®-52 LP

Low viscosity injection resin

Sikadur®-52 LP is a two part, solvent free, low viscosity injection liquids, based on high strength epoxy resins. Suitable for use in hot and tropical climatic conditions.

  • Solvent free
  • Suitable for both dry and damp conditions
  • Shrinkage free hardening
  • High mechanical and adhesive strengths
  • Hard but not brittle
  • Low viscosity
  • Injectable with single component pumps
Inquire Now

Contact us if document is not available

Show all documents

Usage

  • Injection resin with good adhesion to concrete, mortar, stone, steel, and wood.
  • Used to fill and seal voids and cracks in structures such as bridges and other civil engineering, industrial and residential buildings, e.g. columns, beams, foundations, walls, floors and water retaining structures.
  • Effective barrier against water infiltration and corrosion promoting media.
  • Structurally bonds concrete sections together.
 

Advantages

  • Solvent free
  • Suitable for both dry and damp conditions
  • Shrinkage free hardening
  • High mechanical and adhesive strengths
  • Hard but not brittle
  • Low viscosity
  • Injectable with single component pumps

Packaging

Pre-batched

Part A+B : 4 kg unit

Bulk packaging

On request

Product Details

Product Information

Composition

Modified solvent-free two-part epoxy resin

Shelf life

24 months from date of production if stored properly in unopened, undamaged and sealed original packaging

Storage conditions

Store in dry conditions in original sealed packaging and at temperatures between +5 °C and +30 °C. Protect from direct sunlight and heat.

Density

+20 °C

Part A+B mixed (2:1)

~1.06 kg/l

Viscosity

Temperature

Part A+B mixed (2:1)

+10 °C

-

+20 °C

~330 MPa

+30 °C~150 MPa
+40 °C~95 MPa
 
Technical Information

Compressive strength

≥70 N/mm2 (7 d / 30 °C)

(ASTM D695)

Tensile strength

~27 N/mm2 (7 d / 30 °C)

(ISO 527)

Tensile adhesion strength

Curing time

Curing temperature 25 °C

2 days

≥7 N/mm2

14 days

≥10 N/mm2

Application

Application Information

Mixing ratio

A : B = 2 : 1 parts by weight and by volume

Substrate temperature

+25 °C min. / +40 °C max.

Substrate moisture content

Dry or damp (SSD - Saturated Surface Dry: No standing water)

Pot Life

Temperature

1 kg mixture

+5 °C-

+10 °C

-

+23 °C

~70 min

+30 °C~30 min
+40 °C~10 min

The potlife begins when the resin and hardener are mixed. It is shorter at high temperatures and longer at low temperatures. The greater the quantity mixed, the shorter the potlife. To obtain longer workability at high temperatures, the mixed injection resin may be divided into portions. Another method is to chill components A+B before mixing them (not below +5 °C).
Consumption

Consumption

1 kg of Sikadur®-52 LP is equal to ~1 L of injection resin
Application steps

SUBSTRATE PREPARATION

Requirements:

Substrates must be sound, clean, free from oil and grease, old coatings and surface treatments etc.

Pre-treatment for good bond:

Concrete, mortar, stone should be thoroughly prepared by high pressure water jetting or mechanical means such as grinding, chiselling etc. Cracks must be cleaned to remove dust by using compressed air.

MIXING

Pre-batched packaging:

Add all of Part B to Part A. Mix with an electric mixer at slow speed (max. 250 rpm) for at least 3 minutes. Avoid entraining air.

Bulk packaging:

Add both parts in the correct proportion into suitable clean and dry container, mix in the same way as for the pre-batched units.

 

CLEANING OF EQUIPMENT

Clean all tools and application equipment with Sika® Colma-Cleaner immediately after use. Hardened / cured material can only be mechanically removed.

Documents