Sikalastic®-822
Sikalastic®-822 is a 2-part elastic, crack bridging, hand applied polyurethane membrane. Suitable for use in hot and tropical climatic conditions.
- Excellent crack bridging properties
- Highly elastic waterproofing membrane
Usage
- As waterproofing membrane underneath hot poured asphalt on bridge and car park decks
- As waterproofing membrane for other concrete structures and non-trafficed concrete areas with an additional top coat for UV protection
- As repair kit for Sikalastic®-821 LV and Sikalastic®-851 (R)
- As waterproofing for upstands and details on torched bituminous membranes
Advantages
- Excellent crack bridging properties
- Highly elastic waterproofing membrane
Packaging
Part A: 21 kg drum
Part B. 14 kg drum
Colour
Grey, approximately RAL 7005
Product Details
APPROVALS / CERTIFICATES
- Polymer Institute Dr. Stenner GmbH, test report P 1700-1 and P1700-2, confirmation with requirements of ZTV-BEL-B, part 3, 1995
- Kiwa Polymer Institute, test report 5879, additional testing according ETAG 033
- Otto-Graf-Institute, Unversity of Stuttgart, test report 16-31835, fire behaviour according DIN 4102, part 7
Composition
2-component polyurethane resin
Shelf life
6 month from date of production
Storage conditions
Store properly in original, unopened and undamaged sealed packging in dry conditions at temperatures from +5 °C to +25 °C. Protect from direct sunlight and frost.
Density
Part A: ~1.69 kg/l
Part B: ~1.05 kg/l
Mixed resin: ~1.33 kg/l
Solid content
~96 % by weight
Viscosity
Part A: ~14500 mPas
Part B: ~9300 mPas
Tensile Strength
~4.4 N/mm² | DIN 53504 |
Crack Bridging Ability
Up to 0.3 mm at -20 °C
Chemical Resistance
Resistant to de-icing salts, bitumen and alkalis
Temperature Resistance
Short term resistant to mastic asphalt up to +240 °C
Application
Mixing Ratio
Part A : Part B = 60 : 40 (by weight)
Layer Thickness
Min. 2 mm
Ambient Air Temperature
+8 °C min. / +40 °C max.
Relative Air Humidity
Max. 85 %
Dew Point
The substrate and the uncured membrane must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the membrane finish. Beware of condensation
Substrate Temperature
+8 °C min. / +40 °C max.
Substrate Moisture Content
< 4 % according CM method
Pot Life
Temperature | Time |
+10 °C | ~40 min |
+20 °C | ~30 min |
+30 °C | ~20 min |
+40 °C | ~10 min |
Waiting Time / Overcoating
Before applying Sikalastic®-823/ Sikalastic®-825 allow:
Temperature | Minumum | Maximum1) |
+10 °C | 16 h | 1 month |
+20 °C | 12 h | 1 month |
+30 °C | 10 h | 1 month |
+40 °C | 8 h | 1 month |
1) Assuming that dirt has been removed properly and contamination is avoided
Consumption
~1.33 kg/m²/mm
MIXING
Prior to mixing stir part A mechanically. When all of part B is added to part A mix continuously for 3 minutes until a uniform mis has been achieved.
To ensure thorough mixing pour material in a clean container and mix again to achieve consistent mix
Over mixing must be avoided to minimise air entrapment.
APPLICATION
Sikalastic®-822 is poured and than spread evenly with a notched / toothed trowel. Roll immediately in cross wise with a spiked roller to ensure even thickness and
to remove any entrapped air.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with Thinner C immediately after use.
Hardened and/or cured material can only be removed mechanically.